| >>> Offering IEEE 802.1P priority, the STE-326-X3XM provides 3 modes of priority. |
| First-in-first Service: the switch will transmit earlier received data package first. |
| All-High-Before-Low: the switch will transmit high priority data package first. |
| Weight-Round-Robin: the switch will transmit data package according to the queue weight, transmit high |
| priority data package and low priority data alternately. The data package that are for low priority will not be |
| delay or rejected in this way. |
| |
| >>> Providing Class of Service ( COS ): |
| With class service configuration and priority control, the STE-326-X3XM implements Qos function.It supports |
| data pakages' high and low priority, three modes of priority mode. If some port's Port Base is chosen, and |
| high priority is enabled, all data package gets into this port will be mapping as high priority. |
| If VLAN Tag is chosen, the switch will unscramble 3- digit priority mark in Vlan-Tag data package |
| automatically, if that mark is high priority, it will be mapping as high priority.If IP TOS/DS is chosen, |
| the switch will unscramble 8- digit mark in IPV6/IPV4 data package automatically, if this mark is high priority, |
| it will be mapping as high priority. |
| |
| >>> VLAN Multi to One |
| This function regards ports as target VLAN, other ports can add into this target VLAN port as a VLAN group. |
| But after this function is active, the original setup of the VLAN group may be replaced or cleared. |
| |
| >>> Broadcast Storm Control |
|
Broadcast Storm Max Value refers to the Broadcast Storm Limited Value, for example, if Broadcast storm
|
| packets received at 100Mbps in 10ms reach 127 (or the pre-set Max Value), switch will detect that Broadcast |
| Storm is happening. And it will start the Broadcast Storm Control function and give up the unnecessary |
| broadcast storm packets. |
| |
| >>> Port Mirroring: |
| To monitor more than one port at the same time, supports port monitoring receiving, port monitoring sending |
| and port monitoring of receiving and sending modes, supports monitoring across different VLANs |
| |
| >>> Port Bandwidth Control: |
| port bandwidth control enables you to control the transmission rate of each port, including upstream and |
| downstream, and stop the user of a certain port from using too much bandwidth. And user of other ports will |
| have more stable bandwidth. This function can be used in net café or broadband connection to smart |
| residential area. |
| |
| >>> Trunk: |
| Trunk is usually called port aggregation, mainly used for hot backup, fault tolerant in uplink pipeline between |
| switches. Each port can be set to have 2 or 4 ports, port set to trunk group can be used only in trunk group, no |
| matter whether the port is being used in the trunk group or not. |
| |
| >>> STE-326-X3XM Main Features: |
| > 2 Port 100Base-FX + 6 Port 10/100Base-TxHalf/Full duplex switch ports |
| > 2048 MAC address table (4-way hashing) |
| > Two queues for QOS (1:2 or 1:4 or 1:8 or 1:16) |
| > Port-based, 802.1p and IP TOS priority |
| > Store & forward architecture and performs forwarding and filtering at non-blocking full wire speed |
| > An aging function and 802.3x flow control for full duplex and a backpressure function for half duplex |
| > Packet lengths up to 1522 bytes |
| > Congestion Flow Control (HOL) |
| > IEEE 802.1Q Port-based VLAN and adjustable VLAN to support up to 32 VLAN groups |
| > Broadcast storm filter |
| > Port Mirroring |
| > Remote Management by Telnet |
| > Web management |
| > SNMP management |
| > Configure Half/full duplex, auto-negotiation and data-communication via web interface. |
| |
| Network Protocols: |
| > IEEE802.3u 100Base-FX optical Ethernet |
| > IEEE802.3ah 100Base-BX10 |
| > IEEE802.3x flow control |
| > IEEE802.1p priority |
| > IEEE802.1q VLAN |
| > TCP/IP, DHCP |
| |
| Specification: |
| |
|
Protocol
|
CSMA/CD
|
|
Standards
|
IEEE 802.3, IEEE 802.3U, IEEE 802.3X,IEEE 802.1P,IEEE 802.1Q
|
|
Transimission rate:
|
10/100mbps
|
|
Number of Ports
|
6 Port 10/100Base-Tx + 2 Port 10/100Base-Fx
|
|
Physical Connector
|
Tx: RJ45 FX: SC, ST, FC
|
| Wave length: |
Multimode Fiber: 850nm, 1310nm, Singlemode Fiber: 1310nm, 1550nm |
|
Transmission Rate
|
10Mbps: 14880pps, 100Mbps:148800pps
|
|
Switching mode
|
Store and Forward
|
|
Flow control mode
|
IEEE 802.3x full-duplex flow control and back pressure flow control
|
|
LED Indicator
|
LED status of Link, activity, Full/half duplex, speed, and power on diagnostic function
|
|
Cable Support
|
10Base-T: 3, 4 or Cat 5 shielded / unshielded twisted pair, 100 meters max.,
|
|
100Base-TX: Cat 5 shielded / unshielded twisted pair, 100 meters max.
|
|
100Base-Fx: 8.3μm, 8.7μm, 9μm and10μm on single mode fiber and 50, 62.5 and 100μm on multi-mode fiber
|
|
Fiber Cables
|
Single Mode/Multi Mode fiber cable
|
| Stability: |
0.2mw/ ℃ |
| Power Consumption |
～ 5W |
|
Power supply
|
AC:220V or DC:-48V, 50~60Hz
|
|
Temperature Humidity
|
|
Temperature
|
Humidity
|
|
Operation
|
-20 ℃ to 70 ℃
|
10% to 90%
|
|
Storage
|
-40 ℃ to 75 ℃
|
5% to 95% RH
|
|
Dự Án 0932096866
Kinh Doanh Dự án: 093209.6866
Phân phối Dự Án: 083467.8989
Chương trình Khuyến mại Quý 3 năm 2022
Khuyến mại 30.6.2019 - 30.7.2019
Hướng dẫn sử dụng UPS ZLPOWER 1000VA
Sản phẩm cùng loại 
